Polaris ranger 1000 oil filter wrench size

To change the engine oil and oil filter on your Sportsman or XPdo the following:. Place a drain pan under the crankcase. Tip: Place a rag in the bottom of the drain plug to prevent splashing of oil. Remove the drain plug with a 6mm Allen socket. Allow the oil to drain completely. Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin.

Install a new sealing washer part number on the drain plug. The sealing surfaces on the drain plug and crankcase should be clean and free of burrs, nicks or scratches. Place the drain pan beneath the oil filter. Using a 2. Lubricate the O-ring on the new filter with a film of fresh engine oil. Check to make sure the O-ring is in good condition.

The filter is included in both oil change kits. Remove the dipstick. Add the proper amount of the recommended oil, which is 2 quarts 1. Your Polaris Oil Change Kit comes with the correct amount of oil for your vehicle. Do not overfill. The oil change kit for a Sportsman or XP is part number Check the oil level. Add oil as needed to bring the level to the upper mark on the dipstick. Programmable Service Interval The service interval counter on your Sportsman decreases as engine operation hours increase.

Change your engine oil and filter at the recommended service intervals. To reset service hours after they have counted down to "0. For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator. Maintenance tips, procedures and specifications can be found in your Owner's Manual. Skip to content Skip to navigation Skip to footer.

To change the engine oil and oil filter on your Sportsman or XPdo the following: 1.Always check and change the oil at the intervals outlined in the Periodic Maintenance Chart found in your Owner's Manual. Always change the oil filter whenever changing oil. Access the oil check dipstick through the right rear wheel well. Access the oil fill cap through the service access panel on the floor of the cargo box. The crankcase drain plug is located on the bottom of the crankcase.

Access the drain plug through the access hold under the crankcase. Place a drain pan under the engine crankcase. Tip: Place a rag in the bottom of the drain pan to prevent the splashing of oil.

POLARIS 2540086 - Alternative oil filters

Remove the drain plug with a 6mm Allen socket. Allow the oil to drain completely. Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin. Remove the seats by pulling the lever at the back of the seat and pivoting forward to remove. With the seats out of the way, remove the oil filter access panel by pulling out and lifting straight up.

Using a 2. Using a clean dry cloth, clean the filter sealing surface on the crankcase. Make sure the old filter O-ring is completely removed. Lubricate the O-ring on the new filter with a film of fresh engine oil.

polaris ranger 1000 oil filter wrench size

Check to make sure the O-ring is in good condition. Install the new filter. It is included in both oil change kits. Inspect the drain plug and sealing surfaces. Install a new sealing washer on the drain plug. The sealing washer is part number Notice: The sealing surfaces on the drain plug and crankcase should be clean and free of burrs, nicks or scratches.

Clean the sealing surface and reinstall the drain plug. Torque to 12 ft-lbs 16 Nm. Fill the engine with 2. Your Polaris Oil Change Kit comes with the proper amount of oil. Check the oil level and add oil as needed to bring the level to the upper mark on the dipstick.

Wipe up any residual oil that may have collected on vehicle components. Reinstall the seats by aligning the front tabs and pushing down on the rear.

In addition to changing the oil, make sure to grease the propshaft and clean the spark arrestor. To remove the spark arrestor, loosen the spark arrestor fastener with an 8mm socket and pull the spark arrestor out to clean.

Reinstall the spark arrestor and fastener. Torque to 8 ft-lbs 11 Nm. Programmable Service Interval The service interval counter on the instrument cluster of your RZR is programmed to 25 hours at the factory.

As hours of engine operation increase, the counter decreases.Always change the oil and filter at the intervals outlined in the Periodic Maintenance Chart found in your Owner's Manual. Always change the oil filter whenever changing oil. When changing the oil on your vehicle, always wear safety glasses and nitrile gloves. Always remove all cargo from the cargo box before lifting the box to access engine components.

Access the oil fill cap 2dipstick 1 and filter under the cargo box. The crankcase drain plug is located on the bottom of the crankcase. Access the drain plug through the access hole in the skid plate under the crankcase. Stand clear and pull up on the cargo box release lever. Lift the front of the cargo box. For maximum clearance in the engine compartment, detach the cargo box shock from the base of the box.

Carefully detach the fuel line and spark plug wires from their retaining clips on the outlet hose and then loosen the outlet hose clamp and remove the hose from the clutch cover. Caution: Do not allow debris or other objects to enter the clutch cover. Clean the area around the crankcase drain plug.

Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin. Place a drain pan under the engine crankcase and remove the drain plug with a 6mm Allen socket.

Oil Filter, Genuine OEM Part 2520799, Qty 1

Allow the oil to drain completely. Using a 2. Lubricate the O-ring on the new filter with a film of fresh engine oil. Check to make sure the O-ring is in good condition. Reinstall the drain plug with a 6mm Allen socket. Torque the drain plug to 12 ft-lbs 16 Nm.

Remove the oil fill cap and add 2. Reinstall the cap. Reinstall the dipstick completely. Remove the dipstick and check the oil level. Remove the oil fill cap and add oil as needed to bring the lever to the upper mark on the dipstick. Do not overfill. Reinstall the outlet hose to the clutch box, routing the hose under the fuel line and spark plug wires.

Make sure the clutch cover rib aligns in the notch at the end of the outlet hose. Tighten the clamp. Reinstall the fuel line and spark plug wires to the retaining clips on the outlet hose. As hours of engine operation increase, the counter decreases.

The wrench icon will flash for about 10 seconds when the counter reaches zero and each time the key is turned on thereafter until the counter is reset.

When this feature is enabled, it provides a convenient reminder to perform routine maintenance. Refer to the recommended oil change intervals.Always change the filter whenever changing the oil. For youth models, perform a break-in oil and filter change at 5 hours or one month of use. Then change the oil and filter at: 10 hours or miles km ; 25 hours or miles km ; 50 hours or miles km ; and every 25 hours or miles km after that.

While following the Periodic Maintenance Chart is best, understanding why your oil needs to be changed also is a critical part of maintaining your vehicle. Changing your oil at the recommended intervals will ensure consistent and reliable performance for the life of your vehicle. Vehicles subjected to heavy or severe use patterns must be inspected and serviced more frequently.

Pay special attention to the oil level. A rise in oil level during cold weather can indicate contaminants collecting in the oil sump or crankcase. Change the oil immediately if the oil level begins to rise. Monitor the oil level. If it continues to rise, discontinue use and determine the cause.

Your Polaris Dealer can assist. To find a dealer near you, use the Dealer Locator. Your comments are important for us. We will review your suggestions to see how we can improve this article. Skip to content Skip to navigation Skip to footer. When to Change Your Oil. Severe use includes: Frequent immersion in mud, water or sand Frequent or prolonged operation in dusty environments Racing or race-style high RPM use Prolonged low speed, heavy load operation Extended idle Short trip cold weather operation Pay special attention to the oil level.

Thank you. Was this article helpful? Yes, it answers my question. No, it's missing information or visuals. No, the instructions are unclear. No, What are the next steps?Place a drain pan under the engine crankcase.

Tip: Place a rag in the bottom of the drain pan to prevent the splashing of oil. Remove the drain plug with a 6mm Allen socket and allow the oil to drain completely. Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin. While the oil is draining, turn the oil filter counter-clockwise with a 2. Using a clean dry cloth, clean the filter sealing surface on the engine crankcase.

Lubricate the O-ring on the new oil filter with a film of fresh engine oil. Ensure the O-ring is in good condition. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface. Then turn it an additional three quarters of a turn. The filter is part number The filter is included in both oil change kits.

polaris ranger 1000 oil filter wrench size

Replace the sealing washer on the drain plug. The sealing washer is part number Notice: The sealing surfaces on the drain plug and crankcase should be clean and free of burrs, nicks or scratches.

Reinstall the engine oil drain plug. Torque to 12 ft-lbs 16 Nm. Reinstall the dipstick fully and remove again to check the oil level.

Parts Search

Add oil as needed to bring the level to the upper mark on the dipstick. In addition to changing the engine oil, make sure to grease the propshaft and clean the spark arrestor.

Reinstall the spark arrestor and fastener. Torque to 8 ft-lbs 11 Nm. As hours of engine operation increase, the counter decreases. The wrench icon will flash for about 10 seconds when the counter reaches zero and each time the key is turned on thereafter until the counter is reset. When this feature is enabled, it provides a convenient reminder to perform routine maintenance. Refer to the recommended oil change intervals.

Press either toggle button 5 to cycle to the "Service Hours" option. Press MODE to select. Press MODE to reset the existing value and exit or press either toggle button to change the value. Press MODE to save and exit the settings menu. For more information, see your authorized Polaris Dealer.

Skip to content Skip to navigation Skip to footer. Park the vehicle on a flat level surface. Ensure the vehicle is in PARK. Start the engine and allow it to warm up at idle for 2 to 3 minutes. Stop the engine.When changing the oil on your vehicle, always wear safety glasses and nitrile gloves. Always check and change the oil at the intervals outlined in the Periodic Maintenance Chart in your Owner's Manual.

The engine drain plug 2 is located on the bottom of the crankcase. To change the oil and filter 1do the following:.

Position the vehicle on a level surface. Place the transmission in PARK.

polaris ranger 1000 oil filter wrench size

Apply the brakes. Clean the area around the drain plug. The sealing surfaces on the drain plug and crankcase should be clean and free of burrs, nicks or scratches. Place a drain pan beneath the engine crankcase and remove the drain plug with the 6mm Allen socket.

Reinstall the drain plug with a 6mm Allen socket. Torque to 12 ft-lbs 16 Nm. Using a cap-style oil filter wrench, turn the filter counter-clockwise to remove it. Using a clean dry cloth, clean the filter sealing surface on the crankcase. Make sure the old filter O-ring is completely removed. Lubricate the O-ring on the new filter with a film of fresh engine oil.

Check to make sure the O-ring is in good condition. Always clean away all dirt and debris from the dipstick area before removing the dipstick. Remove the dipstick or the oil fill cap on the top of the engine and fill the sump with 2 quarts 1. Reinstall and lock the dipstick or close the fill cap, if applicable.

The oil dipstick is located on the engine, as shown below. Access the dipstick through the right rear wheel well. Re-check the oil level on the dipstick and add oil as necessary to bring the level to the upper mark on the dipstick. Programmable Service Interval When the hours of engine operation equal the programmed service interval setting, the wrench icon 6 on the gauge will flash for 5 seconds each time the engine is started.

When this feature is enabled, it provides a convenient reminder to perform routine maintenance. The service interval is programmed at 50 hours at the factory. The service hours remaining will display in the information display area 3 of the rider information center. Change the engine oil and filter at the recommended service intervals. Press and hold the MODE button to set the new service hour interval.

Your comments are important for us. We will review your suggestions to see how we can improve this article. Skip to content Skip to navigation Skip to footer. To change the oil and filter 1do the following: 1.

Start the engine. Allow it to idle for 2 to 3 minutes.Access the oil dipstick and oil fill cap by tilting the rear cargo box. The crankcase drain plug is located on the bottom of the crankcase. Access the drain plug through the skid plate access hole located directly under the crankcase. Clean the area around the crankcase drain plug.

Use caution when performing this procedure. Do not allow hot engine oil to come into contact with skin, as serious burns may result. Place a drain pan under the engine crankcase and remove the drain plug with a 6mm Allen socket. Allow the oil to drain completely. Remove all cargo from the cargo box. Always remove all cargo from the cargo box before lifting the box to access the engine. Using the 2. Using a clean dry cloth, clean the filter sealing surface on the engine crankcase.

Lubricate the O-ring on the new oil filter with a film of fresh engine oil. Check to make sure the O-ring is in good condition. Install it to specification. The oil filter is part number Both oil change kits include the filter. Replace the sealing washer on the drain plug. The sealing surface on the drain plug should be clean and free of burrs, nicks or scratches. The sealing washer is part number


thoughts on “Polaris ranger 1000 oil filter wrench size”

Leave a Reply

Your email address will not be published. Required fields are marked *